1986 -91 MAZDA RX7 E-PRODUCTION PARTS L IST |
|
|
|
See Many of these parts installed in the Mazdatrix EP RX-7 gallery. |
|
|
|
PART DESCRIPTION |
|
unit cost |
FRONT FIBERGLASS BUMPER AND SPLITTER - now a 2 pc unit |
|
$550 |
EA. |
Full front assembly using right side marker and |
|
|
|
parking light bezel for air intake |
|
|
|
FRONT FIBERGLASS SPOILER - mates to our front bumper facia |
|
$250 |
EA. |
FRONT UNDERTRAY |
|
$250 |
EA. |
Fiberglass and foam with dzuz button receivers installed to match front splitter |
|
|
|
FRONT RADIATOR LOWER DUCTING - fiberglass |
|
$250 |
EA. |
AIRBOX |
|
|
Fiberglass air box designed to fit to e production front end / accepts K&N filter |
|
|
|
*requires a hole cut into radiator bulkhead for passage of air tube to intake* |
|
|
|
AIR FILTER - K&N |
|
$82 |
EA. |
AIR INTAKE TUBE |
|
|
Aluminum tube - 3.5" dia. Formed to fit between airbox and throttle body |
|
|
|
has 1/4 or 1/8 pipe bung fitted for air temp sensor . Polished aluminum |
|
|
|
RADIATOR - HEAVY DUTY - swirl pot , overflow and hoses included |
|
$775 |
KIT |
new crossflow design, extremely efficient,complete installation kit |
|
|
|
RADIATOR AND MOUNT ONLY - heavy duty crossflow |
|
$450 |
KIT |
RADIATOR |
|
|
2.8" Thick aluminum radiator for use in E production and I.T.S. |
|
|
|
RADIATOR WATER TUBES |
|
$145 |
KIT |
aluminum tubes pre fit for our E production radiator. Has lead off for swirl pot |
|
|
|
WATER SWIRL POT / HEADER TANK |
|
$82 |
EA. |
has filler lead and 2 bleeds [ 1/4 npt.] |
|
|
|
OIL COOLER |
|
$641.45 |
EA. |
mazda competition part |
|
|
|
FRONT SWAY BAR - COMPLETE |
|
$435 |
KIT |
speedway bar fitted with our own special bearing blocks , |
|
|
|
will mount in stock location |
|
|
|
FRONT SWAY BAR MOUNTS WITH BEARINGS |
|
$134 |
PR |
our own needle bearing design for free movement of sway bar.for speedway style bar |
|
|
|
FRONT SWAY BAR ARMS |
|
$96 |
PR |
designed to fit 1" speedway bar with A.W.R. bearing blocks / pre-bent |
|
|
|
FRONT ADJUSTABLE SWAY BAR LINKS |
|
$83.50 |
PR |
3/8 left and right rod ends with jamb nuts/ includes hardware |
|
|
|
FRONT SWAY BAR ADJUSTER MOUNT - mounts to control arm for adjuster to bolt to |
|
$20 |
EA. |
FRONT BRAKE DUCTS |
|
$125 |
PR |
mazda competition part |
|
|
|
REAR SWAY BAR COMPLETE |
|
$435 |
KIT |
speedway bar fitted with our own special bearing blocks , |
|
|
|
cannot be used with fuel cell in stock location! |
|
|
|
REAR SWAY BAR MOUNTS |
|
$165 |
PR |
a 4130 rec. tube tig welded that mounts to frame rails to accept |
|
|
|
A.W.R. rear sway bar |
|
|
|
REAR SWAY BAR CHASSIS SUPPORTS |
|
$149 |
EA. |
trianglated rear bar mount support - 4130 tube, tig welded |
|
|
|
FRONT STRUT TUBES |
|
$333 |
EA. |
4130 tube tig welded to accept bilsteins or koni shock inserts for |
|
|
|
for E production ride heights / complete with adjustable spring seats & sleeves |
|
|
|
FRONT BILSTEIN SHOCKS - NON ADJUSTABLE |
|
$165.38 |
EA. |
specialy valved for the E production cars |
|
|
|
FRONT ROLL CENTER BLOCKS / camber control blocks |
|
$45 |
PR |
aluminum spacer blocks to restore front roll center for ITS or E PROD |
|
|
|
FRONT LOWER CONTROL ARMS - COMPLETE |
|
$357.75 |
EA. |
A.W.R designed front lower control arm utilizing |
|
|
|
needle bearings and thrust washers / eliminates all binding / core charge xtra |
|
|
|
PILLOW BLOCKS -FRONT CONTROL ARM |
|
$134 |
PR |
our own needle bearing design for free movement control arm. |
|
|
|
STEERING ENDS - ADJUSTABLE |
|
$146 |
PR |
designed to work with our modified steering rack |
|
|
|
UPPER CAMBER / CASTER PLATES |
|
$240 |
PR |
ADJUSTABLE SPRING SLEEVES |
|
$19.50 |
EA. |
Designed to fit over our strut tubes for spring & ride height adjustment. |
|
|
|
ADJUSTER NUTS (SPRING / RIDE HEIGHT ADJUSTERS) |
|
$19 |
EA. |
PBS TRANSMISSION MOUNT |
|
$240 |
EA. |
4130 rectangular tube mount fits original stock bolt pattern with delron block |
|
|
|
1986-91 E PRODUCTION PARTS LIST |
|
|
|
|
|
|
|
|
|
|
|
PBS CLUTCH PIVOT BALL |
|
$20 |
EA. |
clutch fork pivot ball for 5 1/2 " clutch and flywheel arangment |
|
|
|
RACE DRIVESHAFT |
|
$480 |
EA. |
designed to adapt pbs trans to rx7 differential - specify turbo or non. |
|
|
|
utilizes Mazda Comp. front yoke |
|
|
|
COMPLETE REAR SUBFRAME DIFFERENTIAL BUSHING KIT |
|
$275 |
KIT |
all the rubber bushings replaced with aluminum for precise rear frame alignment |
|
|
|
MODIFIED REAR SUBFRAME |
|
$250 |
EA. |
designed for precise and accurate rear suspension alignment / core charge |
|
|
|
SUBFRAME SUPPORT , REAR - replaces stock part with solid bushings |
|
$100 |
EA. |
ADJUSTABLE REAR TOE LINKS |
|
$263 |
PR |
1/2 " left and right rod ends to allow rapid rear toe adjustments |
|
|
|
CAMBER ADJUSTERS, REAR |
|
$156 |
PR |
billet aluminum/ steel configuration / with or w/out zerk fittings |
|
|
|
REAR OUTER CONTROL ARM BEARING KIT |
|
$198 |
PR |
A.W.R. designed spherical bearing kit to eliminate all rear suspension binding. |
|
|
|
BILSTEIN REAR SHOCKS / AK7107 |
|
$163.09 |
EA. |
specially valved for the Eproduction car |
|
|
|
BILSTEIN REAR SHOCKS / AK7108 |
|
$200.03 |
EA. |
same design as above but with fluid reservoirs for extra suppoort |
|
|
|
HARDWARE KIT FOR BILSTEIN SHOCK / AK7107-7108 |
|
$25 |
EA. |
LOWER MODIFIED SHOCK MOUNT |
|
|
|
UPPER REAR SHOCK MOUNTS / NON ADJUSTABLE |
|
$219.64 |
PR |
upper shock mount with bushings / inc adjuster nut and sleeve for spring |
|
|
|
STAINLESS EXHAUST SYSTEM - COMPLETE |
|
CALL |
|
A.W.R. Design incorporating twin exhaust technology |
|
|
|
STAINLESS HEADER - SEPARATE |
|
|
A.W.R. Designed.Tuned header, built from 321 stainless |
|
|
|
FUEL TANK AND MOUNT / INTERNAL POSITION |
|
$1,200 |
EA. |
internally mounted comes with framework to install |
|
|
|
STEERING COLUMN / ADJUSTABLE |
|
$550 |
EA. |
rx7 collapsible steering column utilizing woodward products |
|
|
|
REAR GLASS BUMPER COVER |
|
$199 |
EA. |
same part as above without any cutouts / stock apperance |
|
|
|
CARBON HOOD |
|
$550 |
EA. |
carbon bidirectional weave / vacuum bagged / eliminates headlight doors |
|
|
|
FIBERGLASS HOOD |
|
$425 |
EA. |
same as above but made from fiberglass-epoxy / eliminates headlight doors |
|
|
|
E PRODUCTION FRONT FENDERS |
|
$220 |
EA. |
designed to fit with our front end but will fit most others |
|
|
|
E PRODUCTION REAR FENDERS |
|
$235 |
EA. |
uses only necessary material for e production / no cutting to fit |
|
|
|
FRONT BRAKE ROTOR HAT - aluminum , for 11.0 rotor to fit stock caliper |
|
$95 |
EA. |
FRONT BRAKE ROTOR - fits with stock caliper |
|
$90 |
EA. |
REAR BRAKE ROTOR HAT - aluminum , fits stock caliper |
|
$95 |
EA. |
REAR BRAKE ROTOR - fits stock caliper |
|
$90 |
EA. |
BRAKE ROTOR ASSEMBLY KIT - A.N. bolts and jet nuts [ 2 rotors ] |
|
$40 |
set |
URETHANE ENGINE MOUNT SET -13 B with or w/out dry sump system |
|
$142.95 |
set |
|
|
|
|
|